1.0级压力表图片

本文章主要介绍了：1.0级压力表图片,过滤器两端是否都要加压力表,0.4mpa压力表检定记录,1.0级压力表图片等信息

该系统符合中型产量矿石实验室样品制备系统的要求，是处理金、镍和铁矿石等的理想选择。
系统特征：
●进样：重量达15kg的块矿等样品
●出样：可将样品快速从110mm破碎到2mm，减少灰尘的产生；
●系统出样尺寸为75um，可选择弃样样品重量及成分样品的份数；
●弃样样品可通过皮带机自动弃样；
●内置的气喷清洗系统可限度的降低样品污染
●系统结构紧凑，占用空间小；
●系统为集成结构，方便运输；
●标准化、定型化使安装简单快速；
●适合于偏远矿山及现场的制样要求；
●极大地降低了样品处理的劳动强度；
●降低了由操作人员误动作引起的偏差；
(1.0级压力表图片)

","Business":"一般压力表；普通压力表；弹簧管压力表；轴向压力表；轴向带边压力表；真空表；真空压力表；船用压力表；船用真空压力表；耐震压力表；船用耐震压力表；不锈钢压力表；耐硫压力表；耐震不锈钢压力表；耐硫抗震压力表；","LastUpdateTime":"2008/7/214:53:23","IsShow":"-999999","IsCharges":"0","PgID":"0","ChargesBeginTime":"2008/7/214:53:23","ChargesEndTime":"2008/7/214:53:23","HitNumber":"963","CreditRating":"0","LocationPic":"1/2008/4000118588068750.jpg","LocationPicDomain":"img42","LogoPic":"1/2008/4000118588912500.jpg","LogoPicDomain":"img42","SkinID":"0","SumClass":"0","SumPro":"0","Sort":"0","UpdateTime":"2008/7/214:53:23","CreateTime":"2008/7/214:52:24","Removed":"0","IsCase":"0","ResNum":"0","DBID":"1","MaxProductsNumber":"0","CityId":"87","WangWang":"","IsSMS":"0","IsLink":"0","GroupID":"2","IsFromImport":"0","CustomTypeBelong":"","CustomShowBelong":"","SupplyOverCount":"0","ComAddrPoint":"","ComAddrPointName":"","MobileLogo":"","MobileLogoDomain":"","IsTrust":"1","MobileStandSkinID":"0","SortRule":"0","ChargesDelayTime":"","IsPurchase":"0","Department":"","RegisteredCapital":"0","AreaID":"0","GoldMember":"0","PurClassID":"0","FrontShow":"0","AfterSaleTel":"","StCClassShowType":"","WebStandTopPhone":"","IsNoCopy":"0","CanRepeat":"0","FeedBackMsg":"","CanLuckyDraw":"0","IsTianYanCha":"0","TianYanID":"0","HeadDomain":"","WechatAccount":"","NickName":"","HeadPic":"","MainMobileKeywords":""}]
(1.0级压力表图片)

V·H·3级（外壳内不充液）
外壳防护等级：IP65
重量：0.2kg(Y-60B-F)
0.6kg(Y-100B-F)
1.0kg(Y-150B-F)
耐震压力表Y100说明书
导压系统及外壳等材质
零件名称
材料牌号
Y-60B
Y-100B、Y-150B
0Cr18Ni9(304)
0Cr17Ni12Mo2(316)
弹簧管
0Cr18Ni9Ti(321)
0Cr17Ni12Mo2(316)
0Cr18Ni9
接头螺纹d
≤60
M14×1.5;Z1/4"(NPT)
≤100
≤35
M20×1.5;
Z1/2";Z1/4"(NPT)
≤125
≤60
轴向嵌装式既轴向前带边、径向嵌装式是指径向前带边、径向凸装式（也叫墙装式）是指径向后带边压力表耐震压力表Y100说明书
(1.0级压力表图片)

往软化水箱内加满水,打开水泵进水口阀门,把水泵放气阀打开,放出水泵内的空气,放出水后把放气阀关闭。接通电源,起动控制箱上手动开关,看电机转向是否正确,把定压罐进水阀门及本系统与需要定压的系统之间阀门关闭。将电接点压力表上下限调好,电控箱转换开关打到自动位置,此时水泵开始运转,将定压罐顶部放气阀打开,然后把定压罐进水口阀门打开三分之一（防止水进入速度过快而损坏内部）,此时水缓缓进入定压罐,等顶部放气阀放出水后,将放气阀关闭,然后把定压罐进水口阀门全部打开,此时电接点压力表压力上升,等压力达到上限设定值后,压力表发出信号传送给控制箱,控制箱发出信号使水泵停止运转。系统调好后打开与需要定压的系统之间的阀门,这样本设备就可以正常起到定压补水的作用.
(1.0级压力表图片)

了解更多关于：不锈钢数字显示压力表，氧气 乙炔压力表损坏的危害，消防电接点压力表是多少伏，变频空调加完氟怎样取下压力表，压力表阀门生产厂家，正压压力表处于负压状态对压力表有损坏，电接点压力表的检验，隔膜压力表属于弹性元件，耐震压力表资料下载，双针压力表生产厂家，压力表的一二比，真空压力表图纸符号，压力表的鉴定证号与有效期，大学生心理压力表，生存战争中的压力表有什么用，锅锅压力表漏水，压力表的使用有效期多久，太阳能压力表无压力，压力表试压选用，制冷用压力表怎么读
本文摘自：http://www.oen1718.com 转载请注明出处